We Are Open 24 Hours a Day, 7 Days a Week, Including Weekends and Public Holidays.

FRP raw material

Applications: Marine, Automotive, Construction, Chemical Corrosion Resistance, Wind Energy, Sports Equipment, etc.

Product PDF एक कहावत कहना

उत्पाद की जानकारी

टैग

1.Classification of Key Raw Materials

(1) Reinforcement Materials (Fibers)

Type	Characteristics	Typical Applications
Fiberglass	Low cost, high strength, corrosion-resistant	Boats, pipes, storage tanks
Carbon Fiber	Ultra-high strength, lightweight (5x stronger than steel)	Aerospace, high-end automotive, sports equipment
Aramid Fiber	Impact-resistant, high-temperature resistant (300°C+)	Bulletproof armor, racing components
Basalt Fiber	Heat-resistant, eco-friendly (made from natural rock)	Fireproof materials, construction reinforcement

(2) Matrix Materials (Resins)

Type	Characteristics	Suitable Processes
Unsaturated Polyester Resin (UPR)	Low cost, fast curing, chemical-resistant	Hand lay-up, spray-up, pultrusion
Epoxy Resin (EP)	High strength, excellent adhesion, moisture-resistant	Aerospace, precision molds
Vinyl Ester Resin (VER)	Resistant to strong acids/alkalis, anti-aging	Chemical tanks, scrubbers
Polyurethane Resin (PUR)	High toughness, impact-resistant, good low-temperature performance	Automotive bumpers, wind turbine blades

(3) Auxiliary Materials

Curing Agents: MEKP (Methyl Ethyl Ketone Peroxide), BPO (Benzoyl Peroxide)

Accelerators: Cobalt salts (e.g., Cobalt Octoate), amines (e.g., DMA)

Fillers: Aluminum hydroxide (flame retardant), calcium carbonate (cost reduction), silica powder (wear resistance)

Release Agents: Wax-based, semi-permanent (e.g., fluoropolymer)

2. Key Performance Parameters

पैरामीटर	Typical Range	Test Standard
Tensile Strength	100-500 MPa (fiberglass-reinforced)	ASTM D638
Flexural Strength	150-600 MPa	ASTM D790
Barcol Hardness	40-60	ISO 2039-1
Heat Deflection Temp. (HDT)	60-250°C (resin-dependent)	ASTM D648
Oxygen Index (Flame Retardancy)	20-55 (≥28 = flame-retardant)	ASTM D2863

3. Material Selection Guide

(1) By Application

Corrosion Resistance (chemical/marine): Vinyl ester resin + fiberglass (surface mat + chopped strand mat)

High Strength & Lightweight (automotive/drones): Epoxy resin + carbon fiber (woven fabric)

Low-Cost Structural Parts (water tanks/pipes): Unsaturated polyester resin + fiberglass woven roving

(2) By Manufacturing Process

प्रक्रिया	Recommended Resin	Recommended Reinforcement
Hand Lay-up/Spray-up	Unsaturated polyester	Chopped strand mat, woven fabric
Pultrusion	Vinyl ester/epoxy resin	Roving, continuous mat
Vacuum Infusion	Epoxy/vinyl ester resin	Multiaxial fabric

4. Storage & Handling Guidelines

Resins: Store in dark, cool conditions (<25°C); keep curing agents and accelerators separate

Fiberglass: Keep dry (humidity ≤60%), avoid fiber breakage

Curing System:

Cold Weather: Use low-temperature curing agents (e.g., acetyl acetone peroxide)

Hot Weather: Reduce accelerator dosage to prevent rapid curing

5. Troubleshooting Common Issues

Issue	Possible Cause	Solution
Incomplete Curing	Insufficient curing agent/low temperature	Increase curing agent or heat environment
Excessive Bubbles	Poor vacuum/resin viscosity too high	Increase vacuum pressure or add thinner
Delamination	Poor fiber wet-out	Use low-viscosity resin or increase pressure